- New Product Information
- Brush Cutting Saws
- Chop Saws & Radial Arm Saws
- Combination Saws
- Dado Sets
- Edge Banders
- General Purpose Saws
- Large Cut Off Blades
- Melamine Saws
- Mitre & Double Mitre Saws
- Nail Biting Saws
- Non-Ferrous Cutting Saws
- NPS Series Panel Saws ~~NEW~~
- Optimizing Saws
- Panel Sizing Saws
- Rip Saws
- Solid Surface Saws
- Special Applications
- Steel Cutting Saws
- Strob Saws-FTG
- Thin Saws
- Tree Trimming Saws
- Trim Saws
- Truss & Component Saws
Rip Saws
Glue Joint Rip Saws
Designed for operations requiring an extra-smooth cut such as solid wood pieces that will be glued together. Use these blades for rip cuts only. Glue Joint Rip Saws can be bored out to fit most gang rip saws. Please call for information and pricing on this service.
| Diameter | Teeth | Bore and Pinhole | Kerf | Plate | Design | Hook | Order ID |
|---|---|---|---|---|---|---|---|
| 10" | 30T | 5/8" | .145" | .102" | TCG | 20 | GJ1030 |
| 10" | 30T | 5/8" | .125" | .087" | TCG | 20 | GJ1030125 |
| 10" | 30T | 70mm, 2key | .125" | .087" | TCG | 20 | GJ1030125K |
| 300mm | 36T | ***80mm, 2 key | 4.2mm | 3.2mm | TCG | 20 | GJRM30036 |
| 300mm | 48T | ***80mm, 2 key | 2.8mm | 2.0mm | TCG | 20 | GJRM3004828 |
| 12" | 36T | 1" | .160" | .118" | TCG | 20 | GJ1236 |
| 12" | 36T | 3 1/8" | .160" | .118" | TCG | 20 | GJM1236157* |
| 12" | 36T | 70mm, 2 key | .160" | .118" | TCG | 20 | GJ1236K |
| 12" | 48T | 1" | .157" | .118" | ATB | 20 | GJ1248ATB |
| 12" | 50T | 1" | .134" | .094" | LRLRS | 20 | GJL1250 |
| 14" | 36T | 1" | .177" | .138" | TCG | 20 | GJ1436177 |
| 14" | 36T | 2", 2 PH | .177" | .138" | ATB | 20 | GJ1436DA** |
| 14" | 36T | 2", 2 PH | .177" | .138" | TCG | 20 | GJ1436DT** |
| 14" | 36T | 3 1/8" | .177" | .138" | TCG | 20 | GJM1436T |
| 16" | 36T | 1" | .177" | .138" | TCG | 20 | GJ1636R |
| 16" | 36T | 2", 2 PH | .177" | .138" | TCG | 20 | GJ1636** |
| 16" | 50T | 1" | .197" | .138" | TCG | 20 | GJ1650 |
| 18" | 48T | 2", 2 PH | .180" | .138" | TCG | 20 | GJ1848** |
Notes
* Designed for Mereen-Johnson rip saws with 3 1/8" arbor and with one 1/4" keyway.
** Specially designed for cutting with Diehl saws, (2) 9/16" pin hole at 5" bolt circle.
*** For Raimann Rip Saw with 4 small 7 mm pins & 2 large 14mm pins, plus 2 keyways.
Multi-Score Split Saws
These blades are used in Multiscore rip applications, with three mounting holes on each half. 8" x 64T (RSMS500) comes with two outside blades with a groover in between for 1/2" wide groove.
| Diameter | Teeth | Bore and Pinhole | Kerf | Plate | Design | Hook | Order ID |
|---|---|---|---|---|---|---|---|
| 8" | 60T | 4 5/16" | .148" | .087" | ATB+R | 0 | RSMS860 |
| 10" | 40T | 4 5/16" | .126" | .087" | TCG | 5 | RSMS1040T |
| 10" | 60T | 4 5/16" | .126" | .087" | TCG | 5 | RSMS1060T |
| 10" | 80T | 4 5/16" | .126" | .087" | HATB | 0 | RSMS1080HA |
| 12" | 60T | 4 5/16" | .126" | .087" | TCG | 5 | RSMS1260T |
| 14" | 80T | 4 5/16" | .150" | .110" | ATB | 5 | RSMS1480A |
Rip & Gang Saws - ATB
These saws are designed to rip soft or hard woods where a strong grain pattern can cause the saw to drift and follow the grain. The ATB design helps maintain direction and provide a clean straight cut. These can be bored out to fit most gang rip saws. Please call for more information.
| Diameter | Teeth | Bore and Pinhole | Kerf | Plate | Design | Hook | Order ID |
|---|---|---|---|---|---|---|---|
| 7 1/4" | 24T | 5/8" | .110" | .079" | ATB | 20 | RS72524 |
| 8" | 24T | 5/8" | .118" | .079" | ATB | 20 | RS824 |
| 8 1/2" | 24T | 5/8" | .118" | .087" | ATB | 20 | RS85024 |
| 10" | 24T | 5/8" | .126" | .087" | ATB | 20 | RS1024 |
| 10" | 30T | 5/8" | .134" | .094" | ATB | 20 | RS1030 |
| 12" | 24T | 1" | .134" | .094" | ATB | 20 | RS1224 |
| 12" | 24T | 70mm, 2 key* | .134" | .094" | ATB | 20 | RS1224K |
| 12" | 36T | 1" | .126" | .087" | ATB | 20 | RS1236 |
| 12" | 36T | 1" | .134" | .094" | ATB | 20 | RS1236134 |
Notes
* RS1224K- 70mm bores have two 20mm x 5mm keyways for SCM Rip Saws.
Rip & Gang Saws - FTG / TCG
These saws are designed to rip soft or hard woods where chiseling action of FTG is effective. FTG grind is the fastest, most efficient tooth design for ripping. 20 degree hook angle for all rip saws.
| Diameter | Teeth | Bore and Pinhole | Kerf | Plate | Design | Order ID |
|---|---|---|---|---|---|---|
| 8" | 24T | 5/8" | .118" | .087" | FTG | RF824 |
| 9" | 24T | 5/8" | .126" | .087" | FTG | RF924 |
| 10" | 10T | 5/8" | .145" | .102" | FTG | RF101 |
| 10" | 24T | 5/8" | .126" | .087" | FTG | RF1024126 |
| 10" | 24T | 5/8" | .145" | .102" | FTG | RF1024145 |
| 10" | 24T | 70mm, 2 key* | .126" | .087" | FTG | RF1024K |
| 10" | 30T | 5/8" | .160" | .118" | FTG | RF1030 |
| 10" | 40T | 3"** | .126" | .087" | TCG | RSLH10403 |
| 10" | 40T | 4 3/16"** | .126" | .087" | TCG | RSLH10404 |
| 10" | 40T | 4 5/16""*** | .126" | .087" | TCG | RSMS1040T |
| 10" | 40T | 5/8" | .126" | .087" | FTG | RF1040 |
| 300mm | 28T | 80mm, 2 key**** | 3.4mm | 2.2mm | FTG | RFRM30028 |
| 12" | 24T | 1" | .126" | .087" | FTG | RF1224126 |
| 12" | 24T | 1" | .134" | .094" | FTG | RF1224134 |
| 12" | 24T | 1" | .160" | .110" | FTG | RF1224160 |
| 12" | 24T | 1" | .185" | .126" | FTG | RF1224185 |
| 12" | 24T | 70mm, 2 key* | .126" | .087" | FTG | RF1224K |
| 12" | 24T | 70mm, 2 key* | .160" | .110" | FTG | RF1224K160 |
| 12" | 30T | 1" | .134" | .094" | FTG | RF1230 |
| 12" | 30T | 1" | .165" | .118" | FTG | RF1230160 |
| 12" | 30T | 70mm, 2 key* | .165" | .118" | FTG | RF1230K |
| 12" | 36T | 1" | .134" | .094" | FTG | RF1236134 |
| 12" | 36T | 3 1/8" | .126" | .087" | FTG | RSM1236F |
| 12" | 36T | 3 1/8" | .126" | .087" | TCG | RSM1236TA |
| 12" | 36T | 3 1/8" | .165" | .118" | TCG | RSM1236TB |
| 12" | 36T | 70mm, 2 key* | .165" | .118" | FTG | RF1236K |
| 350mm | 48T | 120mm, 2 key | 4.2mm | 3.0mm | TCG | RF35048120T |
| 350mm | 48T | 95mm, 2 key, 8 pins | 4.2mm | 3.0mm | TCG | RF3504895T |
| 14" | 24T | 1" | .142" | .102" | FTG | RF1424 |
| 14" | 24T | 1" | .170" | .118" | FTG | RF1424170 |
| 14" | 24T | 1" | .194" | .134" | FTG | RF1424194 |
| 14" | 24T | 3 1/8" | .177" | .134" | FTG | RSM1424T |
| 14" | 24T | 70mm, 2 key* | .142" | .102" | FTG | RF1424K |
| 14" | 30T | 1" | .165" | .118" | FTG | RF1430 |
| 14" | 36T | 1" | .165" | .118" | FTG | RF1436 |
| 14" | 36T | 70mm, 2 key* | .142" | .102" | FTG | RF1436K |
| 14" | 40T | 1" | .170" | .118" | FTG | RF1440 |
| 16" | 24T | 1" | .173" | .126" | FTG | RF1624 |
| 16" | 36T | 1" | .173" | .126" | FTG | RF1636 |
| 18" | 40T | 1" | .185" | .134" | FTG | RF1840 |
| 20" | 40T | 1" | .185" | .134" | FTG | RF2040 |
Notes
*10", 12" & 14" - 70mm bores have two 20mm x 5mm keyways for SCM Rip Saws.
** RSLH comes in 3" or 4 3/16" arbores with 3 pinholes. Fits Lauderdale Hamilton Rip Saw.
*** Multi-Score Rip Saw, Split body, sold as a pair.
**** For Raimann Rip Saw with 4 small 7 mm pins & 2 large 14mm pins, plus 2 keyways.
- © 2024 populartools.net
- All rights reserved.
- Terms & Conditions
- Privacy Policy